Home · All Classes · Modules

QHttpPart Class Reference
^{[QtNetwork module]}

The QHttpPart class holds a body part to be used inside a HTTP multipart MIME message. More...

Methods

• __init__ (self)
• __init__ (self, QHttpPart other)
• setBody (self, QByteArray body)
• setBodyDevice (self, QIODevice device)
• setHeader (self, QNetworkRequest.KnownHeaders header, QVariant value)
• setRawHeader (self, QByteArray headerName, QByteArray headerValue)

Special Methods

• bool __eq__ (self, QHttpPart other)
• bool __ne__ (self, QHttpPart other)

The QHttpPart class holds a body part to be used inside a HTTP multipart MIME message (which is represented by the QHttpMultiPart class). A QHttpPart consists of a header block and a data block, which are separated by each other by two consecutive new lines. An example for one part would be:

 Content-Type: text/plain
 Content-Disposition: form-data; name="text"

 here goes the body

For setting headers, use setHeader() and setRawHeader(), which behave exactly like QNetworkRequest.setHeader() and QNetworkRequest.setRawHeader().

For reading small pieces of data, use setBody(); for larger data blocks like e.g. images, use setBodyDevice(). The latter method saves memory by not copying the data internally, but reading directly from the device. This means that the device must be opened and readable at the moment when the multipart message containing the body part is sent on the network via QNetworkAccessManager.post().

To construct a QHttpPart with a small body, consider the following snippet (this produces the data shown in the example above):

 QHttpPart textPart;
 textPart.setHeader(QNetworkRequest.ContentTypeHeader, QVariant("text/plain"));
 textPart.setHeader(QNetworkRequest.ContentDispositionHeader, QVariant("form-data; name=\"text\""));
 textPart.setBody("here goes the body");

To construct a QHttpPart reading from a device (e.g. a file), the following can be applied:

 QHttpPart imagePart;
 imagePart.setHeader(QNetworkRequest.ContentTypeHeader, QVariant("image/jpeg"));
 imagePart.setHeader(QNetworkRequest.ContentDispositionHeader, QVariant("form-data; name=\"image\""));
 imagePart.setRawHeader("Content-ID", "my@content.id"); // add any headers you like via setRawHeader()
 QFile *file = new QFile("image.jpg");
 file->open(QIODevice.ReadOnly);
 imagePart.setBodyDevice(file);

Be aware that QHttpPart does not take ownership of the device when set, so it is the developer's responsibility to destroy it when it is not needed anymore. A good idea might be to set the multipart message as parent object for the device, as documented at the documentation for QHttpMultiPart.

Method Documentation

QHttpPart.__init__ (self)

Constructs an empty QHttpPart object.

QHttpPart.__init__ (self, QHttpPart other)

Creates a copy of other.

QHttpPart.setBody (self, QByteArray body)

Sets the body of this MIME part to body. The body set with this method will be used unless the device is set via setBodyDevice(). For a large amount of data (e.g. an image), use setBodyDevice(), which will not copy the data internally.

See also setBodyDevice().

QHttpPart.setBodyDevice (self, QIODevice device)

Sets the device to read the content from to device. For large amounts of data this method should be preferred over setBody(), because the content is not copied when using this method, but read directly from the device. device must be open and readable. QHttpPart does not take ownership of device, i.e. the device must be closed and destroyed if necessary. if device is sequential (e.g. sockets, but not files), QNetworkAccessManager.post() should be called after device has emitted finished(). For unsetting the device and using data set via setBody(), use "setBodyDevice(0)".

See also setBody() and QNetworkAccessManager.post().

QHttpPart.setHeader (self, QNetworkRequest.KnownHeaders header, QVariant value)

Sets the value of the known header header to be value, overriding any previously set headers.

See also QNetworkRequest.KnownHeaders, setRawHeader(), and QNetworkRequest.setHeader().

QHttpPart.setRawHeader (self, QByteArray headerName, QByteArray headerValue)

Sets the header headerName to be of value headerValue. If headerName corresponds to a known header (see QNetworkRequest.KnownHeaders), the raw format will be parsed and the corresponding "cooked" header will be set as well.

Note: setting the same header twice overrides the previous setting. To accomplish the behaviour of multiple HTTP headers of the same name, you should concatenate the two values, separating them with a comma (",") and set one single raw header.

See also QNetworkRequest.KnownHeaders, setHeader(), and QNetworkRequest.setRawHeader().

bool QHttpPart.__eq__ (self, QHttpPart other)

bool QHttpPart.__ne__ (self, QHttpPart other)